首页 >> 新闻中心 >> 技术支持

创盈时代阿里巴巴

联系我们创盈时代


猜你喜欢:


四轴冲压机械手

冲压机械手

六轴工业机器人

工业机器人

搬运机器人

搬运机器人


视频案例:


冲床机械手怎么保养和维护?

时间:2017-12-11  来源:本文搜集于网络,由冲床机械手厂家创盈时代整理,欢迎转载,转载请注明出处  点击:304

一 冲床机械手动作测试及限位检测信号的确认检查
Action test of one punch manipulator and confirmation of limit test signal

a 定期测试机械手配件各动作是否有异常现象 如:动作时发出异常响声等
A regularly tests whether there are abnormal movements of the manipulator parts, such as abnormal sound, etc.

b 检查机械手各限位检测开关信号,在机械手动作时,输入,输出的检测信号有无闪烁现象
B checks the switch signals of each limit of the manipulator. When the machine is manual, the signal of the input and output detection is flickering.

c 冲床机械手各限位检测开关是否有因机械手长时间工作而引起的位置移位变化,造成机械手限位检测信号的不良现象

The displacement of the C punch manipulator limits whether the switch has the displacement change caused by the long working time of the manipulator, resulting in the bad phenomenon of the mechanical limit detection signal.


五轴冲床机械手


二 各部位螺丝和连接紧固件有无松脱,由于长时间持续工作各部位的螺丝, 连接紧固件松脱是导致机械手和成型机模具破损的原因
Two, is there any loosening of the screws and fasteners in all parts? Because the screws in various parts and loose fasteners are the reasons for the breakage of the manipulator and the molding machine for a long time.

a 机械手臂上升/下降,引进/引退,横行及旋出刀各固定部位的螺丝,螺母是否松脱
A mechanical arm up / down, introduction / retirement, and spin out the knife with the fixed parts of the screw, the nut is loose

b 上下行程及引进行程调整用的挡板,防落器托架的固定螺丝是否松脱
B up and down stroke and the baffle used for the adjustment of the introduction stroke, whether the fixed screw of the guard bracket is loosened

c 机械手机体单元和控制箱间的继箱内的端子是否松脱
C whether or not the terminals in the box between the body cell and the control box of the mechanical cell phone are loosened

三,气压回路与各部位连接线的检查
Three, inspection of the connection lines between the air pressure circuit and the various parts

a 气管的扭折损伤会影响气压的适当流量
The torsional damage of the a trachea will affect the proper flow of air pressure

b 对机械手进气过滤器内的积水及油污进行清洗
B cleaning the water and oil in the intake filter of the mechanical hand

c 各气管接头或气管有无漏气现象 (造成气压不足)
C air leakage of the trachea or trachea (inadequacy of air pressure)

d 信号连接线的损伤会导致机械手发生误动作或漏电现象
The damage of the D signal connection leads to the misoperation or leakage of the manipulator.

冲床机械手各导致表面污垢的清除及各摩擦部份的定期洽油
The removal of surface dirt from the four punch manipulator and the regular oil of the friction parts

a 机械手上下行,前后和横行用导轨表面上的黄油或垃圾附着所造成的污垢进行定期清理
A regular cleaning of dirt on the surface of a manipulator with butter or garbage attached to the surface of the guide.

b 对冲床机械手配件各摩擦部份及轴承,滑块等部件进行定期洽油及注刀黄油
B regular oil and knife butter for the friction parts of the punch parts of the punch and the bearings, slider and other parts

深圳市创盈时代科技有限公司是一家专注于冲床机械手,上下料机械手,冲压机械手,工业机器人,非标自动化设备的研发生产和销售于一体的国家高新技术厂家。

原文地址:http://www.chytime-robot.com/jszc/405.html

本文关键词:冲床机械手怎么保养和维护

Copyright @ 2016 版权所有:深圳市创盈时代科技有限公司 粤ICP备13087279号-3
联系人:汪小姐  电话:0755-81779389 400-0733-598  手机:18819037886
地址:深圳市沙井沙一社区万安路长兴科技园16栋2楼 网址:http://www.chytime-robot.com
主营产品:五轴冲床机械手  四轴冲压机械手  机床上下料机械手  工业机器人  六轴关节机器人  网站地图  XML